My newest headset conversion kits are ready to go! I have three models. One for older MC2/MC3 Kleins (top bearing loads from the bottom of the headtube), one for MC3.1 Adroits (top bearing loads from top), and one for MC3.1 Mantras (top bearing loads from top).
These kits convert the Mission Control bearings to standard Cane Creek 1 1/8″ IS bearings. Kits include an Aheadset with full compliment semi-cartridge bearings. Fork crown race sits recessed into the lower cup to keep the elements out, upper bearing cap sits dead flush on the top of the headtube to keep water and grit out of that bearing also.
Users can swap bearings to any IS bearing/crown race. They’re all standard parts. If you want to run the super-sealed Cane Creek 110 bearings, they drop right in. Lower crown races with the integrated seal work fine too.
This kit also has the lowest stack height physically possible, so you can run a fork with about 1″ more travel than stock without altering the geometry. Everything sits just about dead flush with the top and bottom of the headtube.
Instructions for the MC3.1 kit are shown below. The MC2/3 kit is undergoing testing currently. Once I’m satisfied that it works 100% I’ll put install instructions up for that unit also.
If you’d like a set for your bike, post a comment here or post in the forums and I’ll get back to you.
Thumbnail Gallery of cups installed in my Carbon Mantra frame
MC3.1 Installation Guide (Click Photos for Larger Image)
Step 1: Remove fork and upper/lower bearings. A plastic hammer and a dowel work well for removing the fork and driving the bearings out.
Step 2: Scrape the old loctite out of the headtube bearing register.
Step 3: Swab out the rest of the remaining loctite with acetone or similar. A clean headtube is key to having the cups sit square.
Step 4: It should look nice and clean like this.
Step 5: Apply some Loctite RC 660 or RC 680 to the headtube. Be sure to get it down into L at the bottom of the bearing register.
Step 6: Apply a thin coat of RC 660 or RC 680 to the upper bearing cup.
Step 7: Insert cup into headtube with a slight twisting motion. If cup is a tight fit, use a wooden block to whack it in. Be sure that it goes in straight (not cocked to once side or the other).
Step 8: When finished it will look like so.
Step 9: Wipe off excess loctite.
Step 10: Upper cup installation finished.
Step 11: Now to the bottom cup.
Step 12: Clean the bottom register with a screwdriver and acetone swab like you did on the upper register. It should look clean and pretty like this when done.
Step 13: Apply RC 660 or RC 680 like you did with the upper register. Again be sure to get some down on the L at the bottom where the bearing cup will rest.
Step 14: Apply RC 660 or RC 680 to the lower bearing cup.
Step 15: Insert with a twisting motion. Use a block of wood to whack the cup in if it’s a tight fit.
Step 16: Wipe off excess loctite. Should look nice and shiny like this when done.
Step 17: Install crown race. Best way to do this is with a pipe that fits over the fork steerer tube.
Step 18: Install bearing on fork. Install fork into frame. Should look like this. Lowww stack height.
Step 19: Install upper bearing and top cover/compression ring. Top bearing cover should just touch the top of the headtube providing a watertight seal. You can apply some grease on the cover lip, or just leave it dry. Aluminum bearing covers will have about a 0.5 mm gap.
Step 20: Tighten down aheadset top cap so it’s just snug. Fork should turn freely and both upper and lower bearing cups should sit square in the frame (no misalignment).
Step 21: Ready to ride. Enjoy your transformed Klein with its new fork and smoooth heaset.
-David